Blackberry Unlock Using Nextgen Server

Compatibility and supported versions

The client software only works on Windows 2000/XP. Supported GSM Blackberry models: 5xxx, 6xxx, 7xxx. CDMA and iDen Blackberry models can not be unlocked using this software.



Before attempting to unlock your Blackberry with Nextgen Server please check that your phone has compatible firmware installed. To check the software/firmware version simply navigate its menu. Go to Settings or Options, then click About




If you have a firmware/software version of 4.0.X.XXX. no upgrade is required and you can proceed directly to unlocking. If your firmware version is 3.X.X.XXX then you must upgrade your Blackberry. This is quite easy to do.

Instructions for upgrading your desktop and handheld software

Step 1. Download and install Blackberry Desktop V4.1

1. Go to http://na.blackberry.com/eng/support
2. Click on 'Downloads' and select 'Service Packs'
3. Select 'Blackberry Desktop Software V4.1 in the dropdown menu
4. Choose 'Service Pack 1 (English)" or "Serice Pack 1 (Multilanguage)"
5. Download the file to your PC and run the installer
6. You will now be running version 4.1 of the Desktop software

Step 2. Download and install firmware upgrade for your handset

1. Select your network and then select the newest firmware for your phone
2. Download the file and then run the installation on your
   

   Driver Installation and Setup

   
   Download and install the latest client software, this will put a copy of the drivers on your PC.
   
   
   Important!!!
   Shut down any antivirus software running on your PC. It must be SHUT DOWN, not disabled (see your AV supplier documentation on how to do it) while using the client.
   
   
   To install the drivers go to Start > All Programs > JIC Technology > Install Iden Drivers
   If there is any complication these drivers can also be downloaded from the official website.
   1. Turn on your iDEN phone and connect to PC with the USB cable
   2. A New Hardware wizard will appear
      
      
      
      
      
      
      
      
   3. Select "No, not this time" and click "Next"
   4. On the next screen select "Install the software automatically" and proceed to the next step by clicking "Next"
      
      
      
      
      
      
      
      
   5. When prompted with a Windows Logo testing dialogue select "Continue Anyway"
      
      
      
      
      
      
      
      
   6. Drivers are now installed
   7. Next update drivers by running
      Start > All Programs > JIC Technology > Fix Iden Drivers
   
   
   
   
   
   

   Unlocking : Motorola iDen

   iDen unlocking credit
   
   
   Important!!!
   Shut down any antivirus software running on your PC. It must be SHUT DOWN, not disabled (see your AV supplier documentation on how to do it) while using the client.
   If you are using Microsoft Active Sync or Active Sync make sure they are is shut down as well or the client won't be able to communicate with the phone.
   
   
   Important!!!
   Do not desconnect the phone before unlocking process is finished. If you experienced an error don't disconnect the phone and keep trying. Otherwise the credit may be lost.
   
   
   
   
   1. Please read the whole tutorial before proceeding.
   2. Make sure that phone's battery is fully charged. Otherwise unlocking may fail that will result in a lost credit.
   3. Remove the SIM card from the phone.
   4. Ensure the phone is properly connected to the PC. If you get a CHG error when unlocking, try holding cable into phone when unlocking.
   5. Launch client software and enter Username/Password
   6. Make sure "Main Server" is set under Server Settings
   7. Select "Iden" under Phone Setting
   8. Ensure phone is powered on with SIM card out and connected to PC via USB cable.
   9. Press "Unlock Moto Iden" on client software.
   10. In 2-3 seconds phone will be unlocked. Phone will reboot after unlock.
   11. If at any time during the unlocking process you experienced an error, please take a screenshot (Prnt Scrn) and send it to us.
   
   
   
   Note, with Motorola iDen i485 and i870 you have to enter the code each time you reboot the handset.
   
   
   
   Troubleshooting

   If you get " Oops ! CHG error ! " or similar

   1. DO NOT DISCONNECT the phone and try to read the codes again.
   2. Check if SIM card and memory card are removed
   3. Decrease COM port's baud rate to: 115200
      Phone Menu > Settings > Advanced > Baud Rate
   4. You might need to try several times
   5. Upgrade your phone's firmware to the latest version. Download the upgrade utility here.

   
   

   It is very important to follow all of the above steps in the event of CHG error !!!

   
   

   If you get " Corrupt Data "

   1. Perform Master Reset (remember to change your pass code/security code in the instructions below if you have changed them).

   
   
   

   How to perform Master Reset on the following iDen phones
   i1000plus, i1000, i2000plus, i700plus, i550plus, i500plus, i370, i390, i600	i95cl, i90c, i85s, i80s, i30sx	i205, i305, i750
   Enter * # 43 (Your phone will prompt Master Reset ) Select OK once (Your phone will prompt Passcode ) Your passcode is 0000 (Your phone will prompt Master Reset ) Enter security code as 000000 and Press OK Select Yes for Master Reset Select OK for caution: see manual The phone will auto power off Switch on the phone again	Press Menu Scroll and Select Settings Scroll and Select Security Scroll and Select Master Reset Enter security code as 000000 and Press OK Select Yes for Master Reset Select OK for caution: see manual The phone will auto power off Switch on the phone again	Press Menu Scroll and Select Settings Scroll and Select More Scroll and Select Advanced Scroll and Select Connectivity Scroll and Select Master Reset Enter security code as 000000 and Press OK Select Yes for Master Reset Select OK for caution: see manual The phone will auto power off Switch on the phone again

   
   
   
   
   

   Unlocking : Motorola iDen i930

   iDen i930 unlocking credit
   
   
   Important!!!
   Shut down any antivirus software running on your PC. It must be SHUT DOWN, not disabled (see your AV supplier documentation on how to do it) while using the client.
   If you are using Microsoft Active Sync or Active Sync make sure they are is shut down as well or the client won't be able to communicate with the phone.
   
   
   

   Before you start

   1. Make sure you have the latest client version
   2. Make sure you have Treo HTTC drivers downloaded and extracted to a folder on your PC. They can also be found by going to
      C:\Program Files\JIC Technology\JIC Online Server\httc-treo-driver
   
   
   

   Reading Codes

   1. Run client, enter your username and password
   2. Select "Main Server" in "Server Settings"
   3. In phone settings select "iDen" and check off "i930" box
   4. Connect USB cable as supplied with the phone
   5. Press both soft keys and power up. The phone will enter Boot Mode
      
      
      If Windows now detects a new device (this happens the first time you put iDen into the Test Mode):

      1. A New Hardware wizard will appear
      2. Select "No, not this time" and click "Next"
      3. On the next screen select a lower option "Install from a list or specific location" and proceed to the next step by clicking "Next"
      4. Browse to the folder containing Treo HTTC drivers
         C:\Program Files\JIC Technology\JIC Online Server\httc-treo-driver
      5. When prompted with a Windows Logo testing dialogue select "Continue Anyway"
      6. Drivers are now installed
      
      
   6. Click "Unlock Moto iDen" in the client, codes will be displayed in under 5 seconds
   7. Codes are also saved in the log file located in
      C:\Program Files\JIC Technology\JIC Online Server
   
   
   

   Entering Codes

   1. Remove battery from your i930 and unplug the cable
   2. Insert incorrect SIM card (card that is not accepted by the phone)
   3. Power on your iDen phone. At the message "Sim Not Allowed" press "OK"
   4. Using stylus pen enter the unlock code exactly as it appears in the client software
   5. Your cell phone will reset and display "Sim Lock Removed"
   6. Your Motorola iDen i930 phone is now unlocked