History of Changes

• Blackberry Module added, support all latest 210 MEPs. Unlock is FREE, and uses server to calculate Unlock Codes
• If Logger fails somehow, you might still use manual mode (if you know IMEI and MEP)
• All DCT4 RPLs are FREE now (Included ASICs: 2,5,6,7,11)
• Skin changed back to white one (too many users complained)
• Improved mode transition between Main/Boot (timeout increased)
• Fixed problem when upon adding "New Path" in "Paths" module Root directory was empty
• CBUS stack improved, if box is disconnected during work, it tries to connect it again instead of "CBUS ERROR"
• Minor changes and bugfixes
  
  How it works? 1. Run Blackberry Module 2. Install drivers (skip this if done already) 3. Click "Read Phone" 4. Connect phone to computer 5. Unlock using calculated codes

• Added support for NEW Nokia BB5 FBUS CMT Loaders (flashing new phones E52 ST Chip, X3, X6, 5530, etc, etc), supported RAPU,RAPIDO,RAPv4 phones,etc. You can flash your phone using New Protocol, but also manage Reading/Writing Certificates,etc.
• Added support for BB5 FBUS New Protocol APE Loaders
• Added support for Unlock / Relock / Autolock DCT4 RSA Based phones (1661, 5030, 1202, and generally ALL ASIC 11 phones), without patch. Solution is standalone and to unlock one phone takes no longer than 2 seconds.
• Added CS Repair due to Bad Simlock in ASIC11 phones (no patch)
• Latest Nokia Loaders 2010 Introduced (including upgraded RAPv3 old prot algo 9.50)
• Added SD Repair, RPL Calc, etc for RAP3v2 phones (hash E9EFF4BFAA5393217CA6B17755FC3E14)
• Added SIMLOCK BACKUP for SL3 phones (can be restored even after fullerase)
• Added support for NCK Reading, SD Extracting, and more accurate Securtity Analysis for v30.xx phones (N96, 5800, etc) - so called by "mx" team "sl3" but in fact is simple sl2), previous versions gave msg about "Decryption fails"
• Added COM Emulator - now Cyclone Box can work as UNI BOX with UFS Pinout !
• Added one-click analyze / repair of Dynamic Camera Configuration (blank screen, "camera not ready",etc) based phones (DCT4plus, 5310, 7210, 5220, 6700, others) supported Camera Drivers:
  
  GR0103D101260C206C02
  GR0103D101260C213402
  GR0103D10126095A1F05
  GR0103D10126095A1F07
  GR0103D10126095A1F87
  GR0103D1012601022C00
  GR0103D1012601022E05
  GR09733814140C206C02
  GR0973381414095A1F05
  GR0973381414095A1F07
  GR0973381414095A1F87
  GR097338141401022C00
  ISL2TI020000093E2F30
  NI00IIIIRR030C20C607
  NI00IIIIRR03095B1F00
  NI00IIIIRR03095B1F01
  NI00IIIIRR030102F200
  NI00IIIIRR030102F201
  NI00IIIIRR030102F202
  NI00IIIIRR030102F203
  NI00IIIIRR0301035420
  NIMMIIIIRRFF0A021001
  NIMMIIIIRRFF094B2F01
  NIMMIIIIRRFF06150018
  NIMMIIIIRRFF06150110
  ST090404003C06150018
  ST090404004C06150018
  
  
  Added TX2 warning when certificate is being not accepted (common problem while writing RPL)
• Updated Nokia USB Connectivity Drivers to 7.1.22.0
• Upon installation, StoredFiles permission is now set to full to avoid Permission problems (and software is still safe for trojans/etc)
• Folder "StoredFiles" is no longer marked to Delete upon Uninstallation to keep old backup files
• Rewritten BB5 RPL Backup routine, now Certificates are being backed-up first, so even if phone is DEAD, still certs will be backed-up
• Factory defaults after flash are now default ticket (BB5,DCT4)
• Mode transition manager added in firmware v01.37
• Software accept Mode Transmission to "Normal" when phone goes to "Power Off"
• Flash Variants are displayed now in descending order
• SL Array read now upon RPL Backup is Keyb/FBUS Count masked
• Now, all 7 codes are being sent to phone (some phones don't accept +7 codes) - tested on N71)
• Fixed NCK Calculation for some mobiles (Security Section Checksum Error)
• When software detects HWC/CCC/Variant certs mismatch, it tries to write local one from database
• Fixed smartcard not responding for reset in some configurations
• Fixed "Failed to Read SP Info" on older RAPv2 phones
• Path manager - bug "/" fixed
• Fixed problems with StoredFiles managing when software have no enough permissions (occurs on Windows Vista / Win7)
• SX4 Bypass is removed now (no need anymore)
• Improved sending CMT Secondary Loader
• Fixed TX2 test crash when phone is completely erased (TOC erased)
• Added automatic PM upload with field 1,309 after SX4 Authorization (one-click ST_SECURITY_FIX !), Supported 100+ BB5 phones in local database
• Improved Security Analysis, added HWC/CCC/Variant Certs Check
• Box Firmware : 01.0C, Access Violation Fixed
• Runtime Error when "Disable Skins" enabled fixed
• Taksbar problems fixed
• Fixed 1208 UEM Read/IMEI Rebuild
• N73 booting improved (when backing up crt, writing rpl incorrect loaders was assumed before)
• New Nokia Firmware introduced, improved stability a lot
• DCT4Plus relock fixed
• Mode transition improved
• BB5 USB Flashing fixed
• Factory Set problems fixed
• Fixed problems when dealing with RAP3v2 Phones
• Skin manager upgraded to v6.63
• HW Platform is now being readen upon Box Initialization
• Added support for CTF'2010 Platform
• Flashbus writing speed increased about 10%
• Flashbus FUR messages reading speed increased about 40%
• BB5 Booting procedure rewritten, now no problems in phones like 5800,N97,5200,etc..
• After flashing, added average writing speed display
• BootAgent removed, now Bootloader upgrade is managed by middle-loader
• Main Firmware rewritten from scratch, old bugs gone away.
• MPU Added
• Improved Oscillator startup time, box hangup fixed in some cases
• Realtime clock not used anymore, too much hardware problems when box not started
• Fixed booting dead BB5 mobiles
• If bb5 booting fails, SW displays possible reason reported by new firmware
• BB5 is being try to boot now without hardware VCC switch
• Added USB Dualport transactions (increases speed)
• Added old protocols support (tick "Use Old Protocols Loader")
• Upon finding CMT/APE loaders, it shows a find parameters (TX2 line, Requested Protocol Type, etc)
• BB5 flash_block_Data checksum fixed
• Additional flash chip information is now shown upon BB5 Alg Boot (VPP Info, Chip Size)
• Fixed boot when after activating DCT4 FTD phone comes to dead
• Fixed "Failed to decode MSID" when flashing some PPM DCT4 files
• UPP ID is now represented as hex upon Read Info
• Added detection whether Pri/Sec camera exists or is configurable
• Minor changes and bugfixes
• Black Skin introduced
• Fixed DCT4 Unlock not being executed after Flashing Procedure
• Versions snap

• Fixed smartcard issues in some environments (Smartcard is not responding for reset) - Fixed issues when some phones couldn't calculate NCK Codes with new method (Security Section Checksum Error) - Minor changes and bugfixes

• All DCT4+ phones are supported including 1661, 1662, 1208, 5030, etc (please use it only for test DCT4 RSA purposes, full stable installer will be released tonight or tomorrow with some other great and unique features.). Don't forget to upgrade box firmware!

• WORLD'S UNIQUE : Standalone Superdongle Key Calculator Added! No internet, no logs, no time! Calculation time 0.003 sec ! Works for any SL1, SL2 and SL3.
• WORLD'S UNIQUE : Standalone Unlocking/Relocking using RPL Added! No internet, no logs, no time! Calculation time 0.002 sec ! Works for any SL1 and SL2.
• WORLD'S UNIQUE : Standalone SX4 Authorization Added! Box is now emulating Nokia SX4 card
  Internet is not required, no need logs to authorize ANY Nokia Phone, just box! Works for any SL1, SL2 or SL3. Emulated SX4 works with ORIGINAL NOKIA Superdongle keys (no need rebuild SD), Custom keys (made by Cyclone,MT,UB), etc. In case of Authorization fail, it will automatically write and authorize using Custom Keys. Authorization time 0.004 sec ! Supported are RAP and RAPIDO mcu, in case of RAPU phones SX4 Remote Card will be used. After authorization with Cyclone, PHONE STILL CAN be Authorized with ORIGINAL SX4 Card!
• WORLD'S UNIQUE : Cyclone can now authorize Barred Phones (with Correct superdongle keys, but with higher KeyIndex ever used than 0 (possible KeyIndex 0..7), SX4 card can use any higher keyindex at time, when higher key is used, lower keys are automaticly not used in future, and phone requires to use higher key index)
  UB and other custom boxes can't do it as long SX4 emulation is not 100% Nokia-Like
• WORLD'S UNIQUE : Starting from now, Cyclone Box have ability to make _FULL RPL BACKUP_ of BB5 phones! Current existing SW on market creating only some part of RPL (NPC,HWC,Simlock)
• Added SUPER DONGLE KEY extracting (this Original Nokia one, so after writing it back phone still can be authorized with original SX4 card)
• Added CMLA KEY DATA extracting (That means created RPL File by Cyclone is now 100% SAME AS NOKIA'S ONE!)
• WORLD'S UNIQUE : Added BB5 MCU & DSP Timestamps Reader / Diagnostic Tool. This will help diagnostic of downgraded phone, will read Security Block, decode timestamps of current installed SW (and factory one, or Dejan Hack if exists) with FLASH installed MCU/DSP timestamps. Will have ability to FULL REBUILD downgrade security zone (dead06) soon.
• WORLD'S UNIQUE : BB5 Security Block Analyzer added, this will read Security Block and analyze it's health for content of following Security Data: SIMLOCK DATA, SUPERDONGLE KEY DATA, ECC KEYS DATA, DIV DATA, CMLA (DRM) DATA. Also it reads ST_SIMLOCK_TEST and ST_SECURITY_TEST and when problems occur, recommends actions.
• WORLD'S UNIQUE : Standalone BB5 Calculator Added. This calculated BB5 NCK (levels 1-7) for unlocking purposes. Calculated codes works only with phones which have been relocked with Cyclone Box. To calculate code only IMEI is required!
• WORLD'S UNIQUE : BB5 Unlock by NCk/RPL, SD Recalc, SX4 auth using USB !! (once log file is read)
• Upon box upgrade (maintenance) Bootloader in box is synchronized with server to avoid Activation Problems
• Bootagent server upgraded to 1.01, fixed "Box is not activated, ID 09)
• Fixed "Access Violation" when Cyclone Box SW is already launched and connection to box opened
• After BB5 Relock, unlock codes is displayed
• More detailed messages is now shown upon new NCK or RPL calculation
• BB5 Security Code Reading is moved to "UserArea" tab (needed space for MCU/DSP timestamp reading and security block analyzing)
• Total unlock/relock time added after operation is finished (thx to arash)
• Box Firmware version is now checked upon loading of Nokia Module
• If box firmware is obsolete, SW asks for upgrade and doing it automatically
• Selected unlock method is now displayed before RootkeyHash support check
• Upon first reading of NCK Code (Extracting) or RPL Calculation, "CYC" log file is stored in "StoredFiles" and next time upon BB5 Security Actions (Calculation of SD, Extracting NCK, Calculating RPL (Relocking)) phone is no booted anymore and whole process took only 1 second!! Keep in mind calculated CYC file is paired with Box Serial number, so in case if your box serial number is changed-go to stored files and purge all "cyc" files.
• Decrypted AES Subblock of Security Block is now checksum checked (16 bytes checksum at end of block)
• Fixed "This is invalid integer..." when parsing phone with damaged IMEI
• When another copy of Cyclone Software is running, message is displayed instead of errors
• New method of NCK Calculation is now default BB5 unlocking method
• When New Method of NCK calculation is selected, PA_SL is not determined already (saves lots of time)
• Skin Manager updated to v6.54 (more stability)
• When BB5 RPL Don't contain Certificates ( NPC, HWC ) phone isn't booted
• Fixed bug when Flash RPL BB5 Data is being written two times
• Added more verbose debug messages when preparing Boot BB5 Phone
• Garbage characters when dealing with SLPA phones (#pw+___garbage___+1) bug fixed
• New splash screen added
• When Cyclone fails to boot APE subsystem, it shows hint about TX2
• APE subsystem is now no longer booted upon CheckFlashingBus
• Changed "Failed to write CMT Cert Data (3)" message, added TX2 information
• BB5 TX2 Line test added after "CheckFlashingBus"
• Before RPL Write, Software testing TX2 Line and when its faulty (not adapter) it showing appropriate message
• Writing BB5 CMT HWC Certificate from RPL fixed
• Parsing some Simlock Arrays (5130) produced garbage output. Fixed.
• Added support for Cyclone Box HW Rev A11D
  Just download EXE file and replace at C:\Program files\Cyclone Box\ Make sure Installer is installed as well (this one from January, otherwise you will have message RootkeyHash not supported).
  
  You don't need any activations, logs to use this update.
  
  Notes: SX4 Emulation works offline and emulates SX4 card 1:1, in case of failure still server will be used. BB5 NCK Calculator works for phone relocked by Cyclone Only (unlocking using IMEI only, no other data is required). BB5 USB Unlocking and other security tools work only if phone log (by flashbus) has been read before. Update is fast and most of security functions (sd, rpl) work very fast. Don't forget to upgrade your Box Firmware to v01.21.

• Added STANDALONE, FREE (NO LOGS, NO INTERNET!!!) NCK Reader (levels.. pw1..7) for ALL BB5 RAPv3 and RAPIDO phones (including 9ddb new hash, together PA_SL1 and PA_SL2 phones)
• Unlocking Method is now being selected before unlock
• Added BB5 RPL Calc for PA_SL1 phones (using server) for Simlock Repair
• Few changes with BB5 booting, minor bugfixes, cosmetic changes, etc
  
  !! FIRMWARE UPGRADE IS MANDATORY IN ORDER TO USE THIS UPGRADE !! KEEP IN MIND STILL SOME PHONES (I.E. TELCELL MEXICO) CAN'T BE UNLOCKED USING NCK, THIS CASE USE FREE RPLS.
  
  Available Unlock Methods Now:
  • PM308 Recalculation (Standalone, Free)
  • NCK Calculation (Standalone, Free, New Method)
  • NCK Calculation (Standalone, Free, Old Method) Remark: Works only on SL2 Rapido Phones, SW < v30
  • RPL Calculation (Server Based, Need Credits)

• Added new BB5 Unlock, Relock, Autolock, Repair Method by RPL Generation, this uses server and consumes 10 logs whilst your credits amount must be > 100.
• Supported are ALL PA_SL2 Phones, both RAPv3 and RAPIDO, with following hashes:
  
  9A28E119033B91D14D22838C86D0D53C 9DDBFCFE6E73CED7D8C6268C8EB85723 38F312750F686F9FC9B1B3778774A195 BAF3A9C3DBFA8454937DB77F2B8852B1 CAEEBB65D3C48E6DC73B49DC5063A2EE F2D76DFAFD66C7F195F278417DF05888 F682624FFB08F6D955DBE7D9C0485084 FCB5C510AF7F09F313D9BDE85A707CC0
  
  
• Before unlock software will ask you (when possible) if you want RPL calculation. If you don't need unlocking by RPL, simply click NO and old free unlocking methods will be used (PM308+120 recalc, Secure RAM dump and NCK calc on RAPIDO PA_SL2 phones, etc). However there are some phones which might be unlocked only using new method (9DDB - 3600, 5220, 7310, or new 5800 >v.30, new N96, etc)
• After unlock, requested RPL file will be saved to STORED FILES dir, it might be used later after phone chip erase, etc - as a generic backup
• To Autolock/Relock use "Import SL5" function and point to SL5 array file in "UnlockData" dir, with SW comes few generated files
• If you need SL5 file for your network, use "Create SL5" button and enter MCC-MNC, SL5 file will be generated for you and your phone might be relocked
• SL Area might be repaired using UNLOCK button for SL2 phones
• RPL Write bugs fixed ("simlock not accepted" after few tries)
• Path "/" problem fixed
• Memory manager updated to v4.94
• New skin manager introduced (6.53) - removed flash files selection bugs
• GUI redesigned a bit
• Nokia Connectivity Cable Driver updated to v7.1.22
• 2760h RM-391 v06.83 Unlock / Relock added
• 2330c RM-512 v09.55 Unlock / Relock added
• 2330c-b RM-513 v09.55 Unlock / Relock added
• 2720f RM-519 v08.42 Unlock / Relock added
• 2720f-b RM-519 v08.42 Unlock / Relock added
• 2720f RM-519 v09.55 Unlock / Relock added
• 2720f-b RM-519 v09.55 Unlock / Relock added
• SX4 Bypass during BB5 Unlock removed, is no needed anymore
• Fixed USB stack hanging up on some Windows configuration due to invalid hexcodes in BoardCode Revision USB Field
• After Super DCT4 Activation in Credits tab box Security Page is automatically upgraded, no need doing it manually
• New firmware v01.15 introduced - box can switch itself from MAIN mode to BOOT mode (no USB reconnect needed anymore)
• Nokia 6220c, 3600s booting fixed in new firmware
• New Secure bootloader v02.10 introduced
• New bootloader supports more types of smartcards (autobaud, PTS protocol negotiation, etc)
• Secure BootAgent v1.00 introduced in new firmware
• Firmware RTOS Code Updated to v6.0.1
• Slightly code optimizations and stability improvements in new firmware
• Secure Bootloader upgrade introduced after box maintenance
• Added support for Cyclone box HW REV A116, A117, A118, A119, A11A, A11B, A11C

• Fixed permanently bug which prevented box starting main firmware (only bootloader...)
• Added LED-progress upon Main Firmware Boot ; this will help to diagnose bootup problems in future; meanings of LED blinking upon startup below
• Code Optimizations
• RTOS Code Updated to 6.0.0
• GCC Compiler Updated to 4.3.2
• Device Framework Updated to 1.5.0
• Little Bugfixes

• Introduced support for FBUS Flashing RAPU YAMA phones (5630, 6700, 6303)
• GUI Stability improved ; updated Skins Stack
• Fixed Algoboot for BB5 phones in some configurations
• SingleLine BB5 Flashing Speed improved (upgraded to 5.5mbits from 4mbits)
• BB5 Multi-CRT Write bug fixed (mismatched certs when writing more than 1 certs at one time)
• Improved Phone LOCAL/TEST Mode Entry algorithms during unlock and FBUS operatinos
• Access Violation in some configurations, when changing BB5 Vpl / Dct4 Vpl Variant/Product - fixed
• "Set factory defaults - BB5" are now default unticked after flash (useless in case of BB5 phones)
• Repower on boot inverted ; according to firmware v1.0.5 , BB5 Phones are now default re-powered on boot
• By default - USE DEFAULT PROFILE while unlocking DCT4Plus is unticked
• DCT4Plus unlock routines rewritten - patch file is now applied before unlocking
• Fixed problems upon unlocking some units of DCT4(plus) phones, when Initial SP Area is corrupted
• When SIMLOCK IS NOT ACCEPTED during BB5 RPL Write, software trying to write FBUS part again after FLASHBUS part, so if NPC is corrupted, the SL will be restored anyway
• Please don't use "Erase Security" function when writing BB5 PA_SL2 RPL, because SIMLOCK will not be accepted in such case! In order of simlock rebuild, NPC MUST BE CORRECT!
• Improved BB5 RPL Write, when HWC can't be written (N96 - example), other certs being written and whole procedure is not being skipped
• After sending Simlock and Superdongle data, delay added, so PA_SL can recalculate SP and Recreate 308 if needed (previously it wasn't working all times)
• During BB5 Configuration Parse (flash chips, status), now RAM chip is displayed instead of UNKNOWN
• DCT4Plus Security Status is now being displayed upon unlock - either TAMPERED or NOT TAMPERED
• When DCT4Plus Security is NOT TAMPERED, Cyclone automatically makes Security Backup
• When user trying to unlock phone which have protected PM308 Security Block against modification, and there is message "Failed to write Security Block" software is now automatically writing back NPC backup - IMEI
• Erase Security while writing RPL is now by default disabled
• SX4 Bypass during PA_SL2 unlock is now by default disabled
• IMEI 1234567890?, and "?" is not valid integer bug fixed
• Cyclone Box HW Rev A113 support added
• Cyclone Box HW Rev A114 support added
• Cyclone Box HW Rev A115 support added

1. BB5 Booting for 5800,N97,5220 and others fixed
   • Fixed problem when box has been hanging up during BB5 boot procedure
   • Meaning of "Repower on boot" button has been inverted. That means that BB5 phones are now by default repowered during boot (more stability while dealing with dead / stuck / unbootable phones).
   • Fixed box stability during 1208 flash and CP extract, no more "Failed to set Flashbus baud"
   • General Improved FBUS Stack stability
   • Code revised - Small speed improvement during BB5 TX2 Flashing
   • Minor changes/bugfixes
2. Support for new DCT4Plus phones unlock/relock/autolock:
   
   RM-305 1650 v5.91
   RH-105 1208 v5.91
   RH-105 1209 v5.91
   RM-298 2630 v7.60
   RM-299 2630b v7.60
   RM-258 2760 v7.60
   RM-258 2760b v7.60
   RH-64 1600 v6.46
   RH-92 1100ib v6.46
   RH-93 1100i v6.46
   RM-291 v06.81 (missing partial)
   
   
3. New DCT4 Loaders v7.49.00 introduced, this adds support for new flash chips
4. Added new DCT4 UEM CBUS Loaders - ASIC11 UEM IMEI Read problems fixed
5. New BB5 Loaders introduced, adds support for new flash chips. Note that greatly speed improvement was noticed during flash RAP3v3 phones with "slow" samsung flash chip - 00ec2208 - this includes 5200, 5310, etc
6. Old updates also included in this bulkupdater, this includes BB5 RAPIDO NCK Calculator, and DCT4Plus Unlock patches released before (after installer):
   
   RM-392 2680 v6.17
   RM-393 2680b v6.17
   RM-392 2680 v5.28
   RM-393 2680 v5.28
   RM-362 5000d v6.31
   RM-363 5000db v6.31